延迟破胶及强制裂缝闭合技术的研究及应用

采用延迟破胶技术,在压裂施工过程中加入不同浓度的胶囊破胶剂,利用它的延缓释放特性,使植物胶压裂液耐温、耐剪切稳定性增强,并且可以在不造成压裂液的流变性、滤失性和携砂性等过早丧失的前提下高浓度使用胶囊破胶剂。该技术与常规破胶技术相比,延缓释放率达50%,能更有效地清除液体残渣,减少压裂液对储层的伤害。同时由于有延缓破胶的特性,放喷采用相应的措施,可以降低支撑剂沉降速度,形成较好的沉砂剖面,提供高的裂缝导流能力,并且可以降低滤饼和压裂液残渣的伤害。     

浅谈南水北调中线S13标渠道机械化衬砌施工技术

南水北调渠道混凝土衬砌,由于其工程等级属于Ⅰ等,总干渠渠道为Ⅰ级建筑物,且渠底宽度较大,边坡坡度较缓,衬砌分缝较多,无论从资源投入、工效还是工程质量达到设计要求都有相当大的难度,渠道衬砌机施工技术正好解决这个难题,实现了机械化作业,值得在南水北调中线工程渠道施工中推广和应用.     

Alkali-metal Na Adsorption and Promoted Oxidation on Si(100)2×1 Surface

The alkali-metal Na adsorption on Si(100)2×1 surface and its promoted oxidation and Si oxidegrowth have been investigated by means of thermal desorption,work function,Auger electronspectroscopy and photoemission electron spectroscopy.The experimental data showed that therewas a new state,interface electron state,near the Fermi level after the deposition of Na atoms.It wasfound that the presence of Na always caused an increase of the oxygen initial uptake whereas thepromotion of Si oxide growth was observed only at the coverage of Na greater than 0.5 ML.A newmechanism of Na-promoted Si oxide growth is suggested in this paper.     

蒸汽发生器二次侧清洁度的视频检查

立式平管板Ｕ形管束的压水堆核电站蒸汽发生器安装至瞬变工况期间，管板上表面的铁基金属残余物的堆积和外来物的存在，以及商业运行后管板、传热管、管子支撑板等的低流速区域里沉积物的堆积要求进行蒸汽发生器的清洁度检查。介绍了蒸汽发生器二次侧清洁度的视频检查技术。该技术适用于蒸汽发生器安装至瞬变工况和投入商业运行后可能发生污染的各阶段的清洁度检查。     

辨识时变系统遗忘因子算法的收敛性分析

著名的递推遗忘因子算法（ＲＦＦＡ）可以用辨识时变系统参数，具有良好的跟踪性能，本文借助于随机过程理论分析了ＲＦＦＡ的收敛性和稳定性，给出了参数跟踪误差的上下界。     

复合果胶酶加工番石榴果汁的工艺优化

采用法国产的复合液态果胶酶加工番石榴果汁。研究结果表明,最佳工艺条件为:每千克番石榴果浆加入20mL浓度为0.01mL/mL的复合液态果胶酶、pH为3.5、45℃下恒温酶解5￣6h。使用不同的澄清剂对番石榴果汁进行澄清,结果表明,加浓度为0.5%的明胶溶液20mL/kg果汁中的效果最佳。番石榴果汁,保持了原有果实的营养成分和保健功能,有独特的风味。     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.     

室外LED显示及其在交通领域的应用

介绍了室外LED显示技术及其在道路交通信息显示领域中的应用,指出目前国内室外LED显示屏普遍存在的主要问题.结合应用于高速公路收费站的LED显示屏的设计,给出解决或者克服这些问题的方法.介绍了室外LED显示的现状,预测了其发展趋势.     

软式操纵系统中张力调节器的设计研究

软式操纵系统是通过钢索张力来传递操纵力的,钢索张力的变化直接影响飞机的操纵性能。张力调节器就是使钢索在各种状态下保持张力恒定的一种调节装置。对张力调节器的原理、结构形式进行了综合论述,并结合设计实例来说明钢索张力调节器的设计过程及设计中各参数的选取原则。     

基于Solidworks的零件建模的若干方法

介绍零件的Solidworks三维建模的几种方法。利用Solidworks的Toolbox插件构造常见的零件模型;利用Solidworks曲线插入功能构造草图,或利用二维图形设计软件进行草图绘制,然后输出到Solidworks中特征构造。